Product Summary
PeiParts 702849 Force Sensor Kit for Q80 and IX6 automatic cutters using 2.4 by 8.5 mm blades. The sensor detects force acting on the cutting blade and supports accurate cutting head monitoring.
Product Overview
The PeiParts 702849 Force Sensor Kit is an electromechanical cutter part used in the cutting head of compatible automatic cutting machines.
The sensor detects mechanical force acting on the blade during cutting and converts it into a signal for the machine control system. Accurate force information helps the system monitor blade loading and identify abnormal cutting conditions.
A damaged or incorrectly calibrated force sensor may produce unstable readings, repeated alarms, interrupted cutting or inaccurate blade force monitoring. Replacing the sensor can help restore normal operation when a qualified technician confirms that the original component has failed.
Before ordering, send PeiParts the machine model, part number, blade size and clear photos of the original sensor. Our team will help confirm the correct cutter parts before shipment.
Product Specifications
Brand: PeiParts
Part Number: 702849
Related Part Numbers: 704171 and 704567
Product Description: Force Sensor Kit
Product Category: Cutter Parts
Main Compatible Models: Q80 and IX6
Other Referenced Models: MH8, M88, MX and IX Series
Suitable Blade Cross Section: 2.4 by 8.5 mm
Application: Cutting Blade Force Detection
Component Type: Electromechanical Sensor Kit
Material: Metal and Electronic Components
Reference Weight: Approximately 0.25 kg per kit
Condition: New
Order Unit: One Kit
Compatibility Confirmation: Required Before Ordering
Important Blade Size Information
The measurement 2.4 by 8.5 mm refers to the blade cross section. It is not the outside dimension of the force sensor.
Automatic cutters using another blade thickness or width may require a different sensor configuration. Always confirm the blade size, machine model and original part number before ordering.
Main Product Features
- Blade Force Detection
The sensor measures mechanical force transmitted through the blade system during cutting.
- Cutting Head Monitoring
The signal produced by the sensor allows the machine control system to monitor blade loading and detect abnormal operating conditions.
- Suitable for 2.4 by 8.5 mm Blade Systems
The kit is designed for compatible cutter configurations using blades with a 2.4 mm thickness and 8.5 mm width.
- Complete Sensor Kit
The product is supplied as a sensor kit for maintenance replacement. Confirm the included components before payment if your machine requires specific accessories.
- Part Number Identification
Part number 702849 provides an important reference for maintenance teams and purchasing departments.
- Compatibility Checking
PeiParts can compare the machine model, sensor photos, blade size and related part numbers before shipment.
How the Force Sensor Works
The cutting blade encounters resistance as it moves through compressed fabric or other materials.
This mechanical load is transferred to the force sensor inside the cutting head. The sensor converts the applied force into an electrical signal that can be processed by the machine control system.
The system uses this information to monitor cutting conditions. An unusual signal may indicate excessive resistance, an incorrect blade condition, a mechanical obstruction or a sensor problem.
The force sensor is only one part of the complete monitoring system. Wiring, connectors, mounting components, calibration and control settings can also affect sensor performance.
Common Failure Symptoms
Inspect the force sensor and related circuit when the machine shows any of the following conditions.
- Repeated force sensor alarms
- Unstable or inconsistent force readings
- Cutting stops without an obvious mechanical obstruction
- Sensor calibration cannot be completed
- The machine does not recognize the sensor signal
- Visible damage to the sensor body
- Loose or damaged electrical connectors
- Damaged sensor wiring
- Abnormal operation after an impact to the cutting head
- Cutting performance changes after sensor replacement
These symptoms do not always mean the sensor has failed. The wiring, connector, mechanical installation and calibration should also be inspected.
Compatibility Confirmation
Part numbers 702849, 704171 and 704567 appear as related force sensor references in different cutter parts catalogs. They may represent different assemblies, updates or machine configurations.
Do not substitute these part numbers automatically.
Please provide the following information before ordering.
- Machine model
- Machine serial number or version
- Original part number
- Clear photos of the original sensor
- Photos of the product label
- Connector and cable photos
- Blade thickness and width
- Required quantity
- Destination country and postal code
PeiParts will compare the information before preparing the quotation.
Installation and Calibration
Installation should be completed by a qualified automatic cutter technician.
Disconnect and isolate the machine power before opening the cutting head.
Record the original sensor position, cable routing and connector orientation.
Do not pull, twist or sharply bend the sensor cable.
Do not apply impact or excessive mechanical load to the sensor.
Clean the mounting surfaces before installation.
Inspect the connector, cable and mounting hardware for damage.
Install the sensor in the correct orientation.
Tighten the fasteners according to the machine service requirements.
Complete the required sensor calibration after installation.
Run the cutter at low speed and check for alarms or unstable readings.
Do not begin normal production until the sensor test and calibration have been completed successfully.
Quality Checking
Before shipment, the product can be checked for the following items.
- Product part number
- Sensor body appearance
- Connector condition
- Cable condition
- Included kit components
- Main installation dimensions
- Product quantity
Product photos can be provided for confirmation when required.
Why Choose PeiParts
PeiParts supplies cutter parts and consumables for automatic cutting machines used in apparel, automotive interior, furniture, leather and industrial fabric production.
Our team helps buyers identify products using part numbers, machine models, blade dimensions, electrical connectors and original product photos.
Customers can request one force sensor kit, several cutter parts or a complete maintenance parts quotation. Combining multiple products into one shipment can reduce purchasing time and international transportation costs.
PeiParts supports cutter parts buyers in Indonesia, Brazil, the Philippines, the United States, Egypt and European countries.
Packing and Shipping
The force sensor kit is packed to protect the sensor body, connector and related components against moisture, dust and impact during transportation.
Shipping can be arranged by international express, air freight or sea freight according to the order quantity and delivery requirement.
Send your destination country and postal code to receive a suitable freight quotation. Product availability, delivery time and shipping cost will be confirmed before payment.
Frequently Asked Questions
What does the 702849 force sensor measure?
It detects mechanical force acting through the cutting blade system and provides a signal to the machine control system.
What does 2.4 by 8.5 mm mean?
It refers to the blade thickness and width. It is not the sensor size.
Which cutter models use this sensor?
Q80 and IX6 are commonly referenced. Some catalogs also list MH8, M88, MX and IX series applications. Compatibility depends on the machine configuration.
Are 702849 and 704171 the same product?
They are related force sensor references, but they should not be treated as interchangeable without checking the machine version and original sensor.
Can a new sensor be installed without calibration?
Calibration may be required after installation. Follow the machine service procedure before returning the cutter to production.
Does a force sensor alarm always mean the sensor is damaged?
No. Wiring, connectors, calibration, mechanical obstruction and control settings can also cause alarms.
Is this an original or replacement part?
Tell PeiParts whether you require an original or replacement version. The available quality option will be stated clearly in the quotation.
Can PeiParts supply other cutter parts?
Yes. Send your complete parts list with part numbers and quantities for a combined quotation.
Request a Quotation
Please send the following information.
Part Number: 702849
Machine Model
Machine Serial Number
Blade Size
Required Quantity
Destination Country
Postal Code
Photos of the Original Sensor
Photos of the Connector and Label
PeiParts will check compatibility and provide the product price, quality option, availability, delivery time and shipping method.
Contact PeiParts now to source the correct cutter parts and reduce the risk of machine downtime.
Compatibility Notice
Machine manufacturer names and model names are used only to describe product compatibility. PeiParts is an independent supplier of replacement cutter parts.
